What Is Fire Pump Sizing?
Fire pump sizing is the process of selecting a pump with the right flow, pressure, and driver power to supply a fire protection system under worst-case conditions. An undersized pump fails when it is needed most. An oversized one wastes money and can create problems of its own, such as dangerously high pressures in the system.
This guide walks through the basic calculation steps used for fire pumps in industrial facilities. Indian practice usually works in m³/h and bar (or kg/cm²), while US practice uses gpm and psi. The method is the same. New to the topic? Start with our guide,What is Fire Safety?
Contents
Step 1: Determine the Required Flow (Capacity)
Flow is set by the design fire scenario, not by the pump. Typically it is the water needed for the largest credible fire in the plant, such as a storage tank fire with cooling of adjacent tanks, plus any hose streams that must run at the same time. The applicable standard defines which scenario and which allowances to use.
In my field experience, fire water demand in petroleum refineries and oil and gas processing plants is set using OISD standards rather than by choosing a pump size first. Under OISD-STD-116, the fire water system is designed for the larger of two demands: fighting two fires at the same time, or a single fire in the worst-case floating roof tank sinking scenario. For depots and terminals, OISD-STD-117 sets the demand by total tankage. For other industries, IS 13039 gives the basis, with water storage ranging from 1 hour of aggregate pumping capacity for light hazard occupancies to 4 hours for the highest hazard class. In every case, the standard and the edition in force should be checked before the demand is finalized. For how the design fire scenario is set under OISD and IS 13039, see Fire Water Demand in India: OISD vs IS 13039
Step 2: Determine the Required Head (Pressure)
The pump must deliver the flow at a pressure high enough to overcome:
- Elevation: the height from the pump to the highest or most remote point
- Friction losses: pressure lost in pipes, valves, and fittings at the design flow
- Residual pressure: the pressure still needed at the most remote device, such as a hydrant, monitor, or deluge valve
Add these together to get the total required head (in metres) or pressure (in bar).
Step 3: Calculate Hydraulic Power
Once flow and head are known, hydraulic power is the energy actually delivered to the water:
Hydraulic power (kW) = Q (m³/h) × H (m) ÷ 367
Here Q is flow and H is total head.
Step 4: Account for Pump Efficiency
No pump is 100 percent efficient. The power the driver must supply to the pump shaft, called brake power, is:
Brake power (kW) = Hydraulic power ÷ Pump efficiency
Worked example: a pump must deliver 500 m³/h at 100 m head, and its efficiency at that point is 70 percent.
- Hydraulic power = 500 × 100 ÷ 367 = about 136 kW
- Brake power = 136 ÷ 0.70 = about 195 kW
Step 5: Select the Driver
The driver (an electric motor or a diesel engine) must be larger than the calculated brake power. Do not size it at exactly the rated point. The pump’s power demand changes along its performance curve, and the driver must handle the highest demand without overloading. Diesel engines also lose output at high ambient temperature and altitude, which must be allowed for. Always confirm the final selection against the manufacturer’s pump and driver curves.
Pump Performance Requirements
Fire pump standards such as NFPA 20 do not only look at the rated point. They also set limits on the shape of the performance curve, for example the minimum pressure the pump must still deliver at 150 percent of rated flow, and a maximum pressure at shutoff (no flow). These limits keep the pump reliable if demand exceeds the design.

Standby, Jockey, and Number of Pumps
A fire water system is rarely a single pump. A typical setup includes:
- Main pumps, sized for the design demand
- A standby pump with an independent driver, so one failure does not leave the plant unprotected
- A jockey pump, a small pump that keeps the network pressurised so the main pumps do not start for minor pressure drops
Common Sizing Mistakes
In practice, these are the mistakes I have seen most often:
- Confusing gross and usable tank volume. Designing the storage from the total tank height without subtracting the dead volume at the bottom (below the pump suction or anti-vortex plate) and the freeboard at the top. The system ends up short of actual usable water.
- Skipping the hydraulic calculation. Sizing pumps with generic thumb rules instead of calculating the exact flow and pressure needed to reach the most hydraulically remote area, including simultaneous hose streams.
- Oversizing the pump. Choosing a much larger pump out of caution creates very high shutoff pressures, which can overstress pipes, valves, and fittings.
- No allowance for growth. New tanks, units, and buildings are added over the years, but the pump and water storage stay at the original design.
Key Takeaways
- Fire pump size comes from the design fire scenario, not the other way around
- Required flow and head give hydraulic power; efficiency gives brake power
- The driver must cover the highest power demand on the pump curve, not just the rated point
- Storage must be sized on usable volume, and the design should allow for future expansion
- Always verify against the applicable standard and the manufacturer’s curves
Conclusion
Fire pump sizing looks like a simple formula, but good results depend on the right design scenario, careful head calculation, and attention to the full performance curve. Done properly, the pump is the part of the system nobody has to think about on the day of a fire.
Related Articles
- AZF Toulouse Explosion (2001): What Happened and the Lessons for Fertilizer Plants
- API RP 754: Process Safety Incident Classification (Tier 1 to 4)
- MVWS vs HVWS: Medium and High Velocity Water Spray Systems (Coming Soon)
- Ammonia Leak Mitigation: Using Water Spray and Water Curtains Safely (Coming Soon)
- Passive Fire Protection (PFP) in High-Hazard Industrial Facilities (coming Soon)
Pingback: What is Fire Safety? Guide for Industrial Facilities
Pingback: Fire Water Demand in India: OISD vs IS 13039
Pingback: Hot Work Safety: Hidden Fire Hazards and Permit Controls
Pingback: API RP 754: Process Safety Incident Classification (Tier 1 to 4)